DIN EN 853 2SN Hydraulic Hoses: Specifications, Applications, and Selection Guide

DIN EN 853 2SN hydraulic hose is a high-pressure hose construction with an oil-resistant synthetic rubber tube, two braided steel-wire reinforcement layers, and a weather- and oil-resistant rubber cover. It is commonly selected for hydraulic lines on mobile equipment and industrial machinery where pressure, movement, and abrasion make a single-wire-braid hose unsuitable. To choose the right hose, match its size, pressure rating, fluid compatibility, temperature range, bend radius, and end connections to the actual system—not just to the “2SN” designation.

Click here to get more.

This guide explains the construction and typical uses of 2SN hose, then sets out a practical selection and purchasing process. At Hengshui Xinchi Hose Manufacturing Co., Ltd., we help B2B buyers review application details and identify a suitable hose configuration; final selection should always be confirmed against the product datasheet and the requirements of the equipment manufacturer.

Key Takeaways

• “2SN” identifies a hose construction with two braided steel-wire reinforcement layers; it does not specify one universal working pressure for every hose size.
• Typical 2SN hose products are designed for hydraulic oil service, but fluid, temperature, and pressure compatibility must be verified for the specific product.
• Size, working pressure, minimum bend radius, hose routing, and fitting compatibility all affect safe system performance.
• When requesting a quotation, provide the hose size, operating conditions, quantity, delivery destination, and any documentation requirements.

Who This Guide Is For

This guide is intended for hydraulic equipment manufacturers, distributors, maintenance teams, and procurement professionals sourcing hose for original equipment or replacement applications. It is especially useful when a project specifies EN 853 2SN but does not yet provide all the details needed to confirm a complete hose assembly. It is not a substitute for the machine manufacturer’s instructions or a product-specific technical datasheet.

What DIN EN 853 2SN Means

Construction and function

EN 853 is a European hose standard covering specified types of rubber hydraulic hose. In a 2SN hose, “2” refers to two steel-wire braid reinforcement layers, while “SN” identifies the relevant construction type within the standard. The inner tube carries the hydraulic fluid, the wire layers provide reinforcement against pressure, and the outer cover helps protect the hose from the surrounding environment.

The two-braid construction is intended for hydraulic service requiring a higher-pressure hose design than a comparable one-braid construction. However, the designation alone does not tell a buyer the permissible pressure for every nominal bore. Working pressure and other limits are size- and product-specific, so use the manufacturer’s published ratings rather than estimating them from the construction label.

Typical materials and product details

A typical 2SN hose uses a synthetic rubber inner tube selected for hydraulic-fluid compatibility, two high-tensile steel-wire braid layers, and a synthetic rubber outer cover. Exact compounds, cover options, and product tolerances can vary by manufacturer. For applications involving unusual fluids, outdoor exposure, high abrasion, or special cleanliness requirements, request confirmation for the particular hose model.

Commercially available 2SN products commonly cover nominal bore sizes from approximately 5 mm to 51 mm, with exact size availability depending on the supplier. Do not assume that every size has the same pressure rating or bend radius. The product datasheet should state the relevant values for the specific bore and construction.

Specifications to Check Before Ordering

The following figures are useful starting points, not a replacement for the data supplied with a particular hose. Many 2SN products list a working-temperature range of approximately -40°C to +100°C for suitable hydraulic oils; allowable limits may be lower for water-based fluids or other media. Confirm both the hose’s temperature range and the fluid manufacturer’s limits for the intended operating conditions.

Pressure ratings should be checked at the hose size and operating conditions you intend to use. Also consider pressure surges, not only the system’s nominal pressure, and follow the equipment manufacturer’s safety requirements. If the operating pressure or temperature approaches a product limit, ask the supplier to review the application before ordering.

Applications and Matching the Hose to the System

2SN hoses are used in hydraulic circuits on equipment such as construction machinery, agricultural machines, material-handling equipment, and industrial systems. Typical circuits may include pressure, return, or pilot lines, but suitability depends on the line’s pressure, fluid, temperature, movement, and installation environment. A hose appropriate for one circuit may not be appropriate for another, even on the same machine.

If you want to learn more, please visit our website Hengshui Xinchi Hose Manufacturing Co., Ltd..

Consider the full operating environment

Start by identifying the hydraulic fluid and its operating temperature. Then confirm normal and peak pressure, including any recurring pressure spikes, and check whether the hose will experience vibration or frequent flexing. For outdoor equipment, inspect potential exposure to sunlight, ozone, moisture, chemicals, sharp edges, and abrasion.

Route the hose so it does not twist during installation or operation, and keep bends within the specified minimum radius. Leave enough length for movement without allowing the hose to rub against nearby components. Where abrasion or impact is expected, discuss protective sleeves, clamps, or routing changes with the equipment designer rather than assuming the standard cover will resolve every hazard.

A Practical Selection Framework

1. Record the system requirements. Note the required standard and hose type, nominal bore, working pressure, operating temperature, fluid, and installation space.
2. Confirm the size and flow requirement. Use the equipment specification or engineering calculation to determine bore size; avoid choosing a hose based only on the visible outside diameter.
3. Check the pressure and temperature ratings. Compare system conditions with the product-specific datasheet, allowing for the operating conditions and relevant equipment requirements.
4. Review routing and movement. Check minimum bend radius, hose length, vibration, movement, and abrasion points before finalizing the assembly.
5. Match the fittings and assembly method. Confirm thread type, connection geometry, material, and crimp specifications with the hose-and-fitting supplier. Compatibility should be established for the complete assembly, not inferred from the hose type alone.
6. Approve documentation and samples if needed. For repeat orders or a new application, request the applicable datasheet and agree on inspection or sample requirements before production.

Common Selection Mistakes

A frequent mistake is treating “2SN” as a complete specification. It describes the construction category, but buyers still need to confirm size, product-specific pressure rating, temperature limits, and fittings. Another risk is selecting a hose solely by nominal bore while overlooking outside diameter, bend radius, or the space available for routing.

It is also important not to assume that all hydraulic fluids are interchangeable from the hose’s perspective. Fluid composition and temperature can affect the inner tube, while weather, oil, and abrasion exposure affect the cover. When the application includes an uncommon medium or demanding conditions, obtain written compatibility guidance for the offered product.

Pricing, MOQ, and Lead-Time Considerations

Pricing for 2SN hose depends on factors such as bore size, construction details, order quantity, packaging, and whether the purchase is for hose only or assembled hose products. Minimum order quantities and production schedules vary by supplier and item, so they should be confirmed for the requested specification rather than assumed. Custom lengths, special packaging, and documentation requirements may also affect the quotation or schedule.

To support an accurate quotation, provide the requested size range, quantity, preferred delivery terms, destination, and target delivery date. Include any drawing, fitting details, label requirements, or inspection needs. If your project has a firm launch or maintenance deadline, ask the supplier to confirm availability and the expected schedule before placing the order.

Supplier Evaluation Checklist

• Can the supplier provide a datasheet for the exact hose size and construction?
• Are working pressure, temperature range, dimensions, and minimum bend radius clearly stated?
• Can the supplier confirm fluid and cover compatibility for the intended conditions?
• Are fittings, crimping requirements, packaging, and inspection expectations clearly agreed?
• Can the supplier confirm MOQ, production lead time, and export documentation requirements?

At Hengshui Xinchi Hose Manufacturing Co., Ltd., we supply hydraulic rubber hose products and support buyers with specification review and quotation coordination. We recommend that customers share their application conditions and connection details so our team can assess the requested configuration against available product information. Product availability, technical limits, and delivery schedules should be confirmed for each order.

Conclusion: How to Choose the Right EN 853 2SN Hose

DIN EN 853 2SN is a two-steel-wire-braid hydraulic hose construction used in many mobile and industrial hydraulic applications. The right selection is not determined by the 2SN label alone: confirm bore size, pressure rating, temperature and fluid compatibility, bend radius, routing conditions, and fitting compatibility for the complete assembly. Use current product-specific documentation and follow the equipment manufacturer’s requirements.

For your next step, prepare the hose size, operating pressure and temperature, fluid type, application, quantity, connection details, and delivery needs. Send these details to Hengshui Xinchi Hose Manufacturing Co., Ltd. to request a product review and quotation for your sourcing requirements.

Are you interested in learning more about DIN EN853 2SN Hydraulic Hoses? Contact us today to secure an expert consultation!