1.5 Inch Stainless Welded Mesh Panel: Specifications, Applications, and Buying Guide

A 1.5 inch stainless welded mesh panel is a rigid sheet made by resistance-welding stainless steel wires where they cross, with a nominal mesh spacing of 1.5 inches (38.1 mm). It is commonly considered when a project needs open-area screening, partitioning, guarding, or containment with a corrosion-resistant material. The opening dimension alone does not fully define the panel: wire diameter, stainless grade, panel size, edge finish, and whether the spacing is measured center-to-center or as a clear opening also matter. At Shunqiang Wire Mesh, we recommend confirming these details before requesting a quotation so that suppliers price and manufacture the same specification.

For more information, please visit our website.

Who This Buying Guide Is For

This guide is for procurement teams, fabricators, distributors, and project engineers comparing stainless welded mesh panels for industrial or commercial use. It is useful when a drawing specifies a 1.5 inch mesh, but leaves other details open, or when a buyer is converting a general application into a purchase-ready specification. The information below explains the main variables to confirm rather than assuming one universal panel design. Final suitability depends on the working environment, loads, and applicable project requirements.

What a 1.5 Inch Stainless Welded Mesh Panel Is

Mesh spacing and construction

In welded mesh, longitudinal and transverse wires intersect at regular intervals and are joined at those intersections. “1.5 inch” describes the stated mesh spacing, but suppliers may use different conventions, such as measuring from wire center to wire center or defining the clear opening between wires. Those definitions produce different usable apertures, so buyers should request a dimensioned drawing or written confirmation. The panel is supplied as a flat sheet or cut panel, with size and edge treatment agreed for the order.

Material options

Stainless steel grade should be selected for the service environment, not just by name or price. Grade 304 is commonly considered for general indoor and many non-coastal applications, while grade 316 is often evaluated where exposure to chlorides or more demanding corrosive conditions is expected. Neither grade is universally suitable for every chemical, temperature, or exposure profile, and stainless steel can still corrode under unsuitable conditions. Where performance is critical, provide the supplier with details of the environment and confirm the material designation required by the project.

Specifications to Confirm Before Ordering

A complete inquiry should distinguish the nominal mesh spacing from the clear opening and state how each is measured. It should also identify wire diameter, stainless grade, panel width and length, quantity, and any required tolerances. As a unit conversion, 1.5 inches equals 38.1 mm; this conversion does not establish whether 38.1 mm is the wire-center spacing or the clear aperture. For instance, a 3.0 mm wire diameter can be used as an illustrative inquiry value, but it should not be treated as a standard or recommended diameter without checking the application.

Applications and Application Matching

The relatively open spacing may suit applications where airflow, visibility, or passage of larger particles is more important than fine filtration. Potential uses include equipment guards, storage or security partitions, architectural infill, protective barriers, and certain agricultural or industrial enclosures. The appropriate design depends on the expected load, contact risk, installation method, and environment. A 1.5 inch mesh should not be selected as a fine screen when the required particle size is smaller than its openings.

Shunqiang Wire Mesh are exported all over the world and different industries with quality first. Our belief is to provide our customers with more and better high value-added products. Let's create a better future together.

Match the panel to the operating conditions

For a guard or partition, consider the force it may encounter and how the panel will be supported around its perimeter. For outdoor or washdown use, review the stainless grade, cleaning chemicals, drainage, and potential exposure to salts or chlorides. For a fabrication project, check whether the panel needs to be cut, bent, framed, or joined to other components after delivery. If people may handle or approach the panel, specify whether cut wire ends need to be trimmed, covered, or otherwise protected.

A Practical Selection Framework

1. Define the function. State whether the panel is intended for guarding, separation, screening, containment, or another use, and identify any load or access requirements.
2. Resolve the opening definition. Confirm whether 1.5 inches refers to wire-center spacing or clear aperture, and record the required tolerance if one applies.
3. Select material and wire diameter. Describe the environment and performance need, then confirm the proposed grade and wire size with the supplier or project engineer.
4. Set dimensions and finishing details. Provide panel width, length, edge requirements, and any framing or downstream fabrication needs.
5. Review a written specification. Compare the quotation, drawing, and purchase order to ensure they describe the same mesh, material, dimensions, and finish.

Common buying mistakes

A frequent sourcing problem is specifying only “1.5 inch stainless mesh” without defining the opening convention or wire diameter. Another is choosing a stainless grade based solely on an assumption that all stainless steel performs equally in corrosive environments. Buyers can also overlook panel tolerances, edge condition, and packaging, even though these details affect installation and handling. A concise specification sheet helps prevent mismatched quotations and reduces clarification during production.

Pricing, Minimum Order Quantity, and Lead Time

Panel pricing depends on the agreed stainless grade, wire diameter, panel dimensions, quantity, edge or frame requirements, and current material and production conditions. A custom size or additional fabrication may require a different production arrangement than a standard panel, so buyers should share drawings and quantities when requesting a quote. Minimum order quantity and lead time are supplier- and specification-dependent; they should be confirmed in writing rather than assumed from a general product description. For time-sensitive projects, include the required delivery date and destination in the inquiry and ask the supplier to confirm feasibility.

Supplier Evaluation Checklist

Before placing an order, check that the supplier has acknowledged the mesh spacing convention, wire diameter, stainless grade, panel dimensions, tolerances, and edge finish. Ask whether the quotation includes any requested cutting, framing, packaging, or material documentation, and clarify what is excluded. Confirm the order quantity, production schedule, shipping terms, and process for approving a drawing or sample if required. For traceability or regulated projects, state the documentation requirements before production and confirm which documents the supplier can provide.

Working with Shunqiang Wire Mesh

At Shunqiang Wire Mesh, we can review a 1.5 inch stainless welded mesh panel inquiry against the details provided and clarify specification points before quotation. Buyers can send a drawing or list the mesh spacing, spacing convention, wire diameter, grade, panel size, quantity, finish, and destination. If some values are not yet fixed, identify them as open requirements and ask us to discuss available options rather than treating an example value as a confirmed product specification. This helps align the quotation with the intended application and purchasing criteria.

Key Takeaways

• A 1.5 inch nominal mesh spacing converts to 38.1 mm, but the inquiry must define whether this is center-to-center spacing or a clear opening.
• Wire diameter, stainless grade, panel dimensions, edge finish, and tolerances are essential parts of the specification.
• Choose material and panel design according to the actual environment, loads, installation, and project requirements.
• Pricing, minimum order quantity, and lead time depend on the confirmed order details and should be verified with the supplier.

Conclusion: Prepare a Clear Inquiry

A 1.5 inch stainless welded mesh panel can be a practical option for open screening, guarding, partitioning, and similar uses when its spacing and material match the application. To move from product research to a comparable quotation, define the opening measurement, wire diameter, stainless grade, panel dimensions, quantity, and finishing requirements. Include the operating environment and delivery needs so the supplier can assess the request with the right context. Send your specification or drawing to Shunqiang Wire Mesh to discuss a suitable panel configuration and request a project-based quotation.

If you want to learn more, please visit our website 1.5 inch stainless welded mesh panel(vi,ar,ru).